Ideal boiler fault codes: what they mean and what to do
An Ideal fault code tells you why the boiler has stopped. The one people see most is L2, which means the boiler tried to light and failed. F1 means the water pressure is low, and L1 means the boiler got too hot or the water isn't moving. Many of these clear after a few safe checks and one restart. If the code keeps coming back, a Gas Safe engineer needs to find the cause.
Updated 15/11/2026 · Express Contractors
This guide covers the Ideal codes people search for most. It shows what each one means, what you can check, and when to stop. If a code won't clear, you'll need an Ideal boiler repair by a Gas Safe engineer. We fix all makes, Ideal included. The guide is part of our boiler problems series.
How do Ideal boiler fault codes work?
Ideal boilers show a fault in one of three ways, depending on the model. Some show a letter and a number, like L2. Some add a zero, like L 02. Boilers with a bigger screen spell the fault out in words.
- Letter and number: the Logic Combi ESP1, Logic Code Combi ESP1 and Instinct show codes like L2 or F1. Older Logic Combis from around 2011 flash the letter, then the number, in turn. So you may see "L" and "2" blinking one after the other.
- With a zero: the Logic Combi2 (C24, C30 and C35) shows L 02, F 01 or L 09. These mean the same as L2, F1 and L9.
- In words: the Logic+ Combi2, Logic MAX Combi2 and Vogue show the fault's name, such as "Ignition Lockout" or "Low Water Pressure". Match the name to the sections below.
The letter tells you something too. Ideal says an L code means the boiler is in lockout. A lockout is when the boiler shuts down for safety and stays off until it's restarted. An F code means it has found a fault.
One more thing to know. A few codes mean different things on different Ideal models. L5 is a good example. On a Logic Combi ESP1 it points to a temperature sensor. On an Instinct or an older Logic, it means the boiler has been reset too many times. So if a meaning here doesn't fit, check the manual for your model.
Ideal fault codes at a glance
L2, F1, L1 and F2 are the codes you can most often clear yourself. Find your code below and jump to its section. "Restart once" means press restart one time, then call an engineer if the code returns.
| Code | What it means | Can I fix it? |
|---|---|---|
| L2 | The boiler failed to light | Often. Check the gas and the condensate pipe, then restart once. |
| F1 | Water pressure too low | Often. Top up the pressure. |
| L1 | Too hot, or no water flow | Sometimes. Check the pressure and radiator valves, then restart once. |
| F2 | The flame went out | Same checks as L2, then restart once. |
| L9 or F9 | A circuit board problem | No. Call a Gas Safe engineer. |
| F3 to F7, L6, LC, FU and others | A part, sensor or supply fault | Mostly no. See the list for the few you can check. |
| 00, C, d, P | What the boiler is doing, not a fault | Usually nothing to do. |
Safety first
Smell gas? Open doors and windows. Don't use light switches or anything that could spark. Turn the gas off at the meter if you can do it safely. Then go outside and call the National Gas Emergency number on 0800 111 999.
Headaches, dizziness, sickness or a lazy yellow flame? These can be signs of carbon monoxide (CO), a poison gas you can't see or smell. Turn the boiler off, open windows, get everyone outside and call 0800 111 999. See a doctor if anyone feels unwell. Our carbon monoxide advice has more.
Never open the boiler case. Only a Gas Safe registered engineer should take the cover off a gas boiler. The checks in our guides are all ones you can do from the outside.
What does L2 mean on an Ideal boiler?
L2 means the boiler tried to light five times and couldn't, so it has locked out. Ideal calls this an ignition lockout. You may see L 02, flashing L and 2, or the words "Ignition Lockout". A gas supply problem or a blocked condensate pipe is often to blame.
Ideal suggests these checks, in this order:
- Look at the condensate pipe. That's the small plastic pipe that carries waste water from the boiler to a drain. In cold weather it can freeze, often outside.
- Check that your other gas appliances work, such as a gas hob.
- If they don't, check the gas is on at the meter. If you have a prepayment meter, check it has credit.
- Find the yellow gas valve on the pipe under the boiler. It's open when the handle lines up with the pipe.
- Restart the boiler once.
Here's a useful sign. Ideal says a blocked condensate pipe makes the boiler gurgle before it locks out on L2. It may gurgle again when you restart it. Our guide on what boiler noises mean covers gurgling in more detail.
If the pipe is frozen, thaw it with a hot water bottle, a warm damp cloth or warm water from a watering can. Never use boiling water. Ideal also says not to thaw pipes that are above ground level, so stay off ladders. There are full steps in our guide to thawing a frozen condensate pipe.
For a cold spell, Ideal gives this tip. Turn the heating knob on the boiler up to full and set the heating to run all the time. Then turn the room thermostat down to 15°C at night or while you're out. The warm water keeps moving, so the pipe is less likely to freeze. Put the settings back once the cold has passed.
If L2 comes back after one restart, stop. Inside the boiler, the engineer will check the gas pressure, the spark and the flame sensor. They'll also check the gas valve and the trap that collects waste water. If no gas appliance in the house works, call your gas supplier. If the boiler won't respond at all, see our guide to a boiler that won't turn on.
What does F1 mean on an Ideal boiler?
F1 means the water pressure in your heating is too low. You may see F 01 or "Low Water Pressure". Ideal says the boiler won't run below 0.3 bar. You can often fix it by topping up the pressure.
"Bar" is the unit on the pressure gauge. With the boiler cold, the gauge should read 1 to 1.5 bar. To raise it, you use the filling loop. That's a short hose or a pair of taps under the boiler that lets mains water in. On many Ideal Logic boilers, you connect the loop for the top-up, then take it off and refit the cap after.
- Turn the boiler off and let the system cool.
- Open the filling loop slowly and watch the gauge.
- Close it once the gauge reads 1 to 1.5 bar.
- Take the loop off if your model needs it. Have a cloth ready, as a little water can spill.
- Turn the boiler back on.
Your Ideal user guide shows where the loop is on your model. Our guide to a boiler that keeps losing pressure has more detail. If F1 comes back within days, water is escaping somewhere. Ideal says that may be a leak, and it needs a Gas Safe engineer. If your gauge reads too high instead, read our guide to high boiler pressure.
What does L1 mean on an Ideal boiler?
L1 means the water in the boiler got too hot, or it isn't flowing round the system. You may see L 01. Low pressure, closed radiator valves or air in the radiators can cause it. So can a pump that's stuck.
- Check the pressure is 1 to 1.5 bar, and top up if it's low.
- Make sure every radiator valve is open.
- If radiators are cold at the top, bleed them, then check the pressure again.
- Restart once.
Ideal's screen models give a slightly fuller routine. With the boiler off and the system cold, fill to 1 bar. Then bleed the radiators, fill to 1 bar again, check the valves and restart. Our guide to bleeding a radiator shows how. If L1 returns, the pump or a temperature sensor may be at fault. Both sit inside the case, so they need an engineer.
What does F2 mean on an Ideal boiler?
F2 means the flame lit but then went out. Ideal calls it flame loss, and you may see F 02 or "Flame Loss". The causes overlap with L2, so the checks are the same.
Make sure your other gas appliances work and the meter is on. Check any prepayment meter has credit. On a cold day, look at the condensate pipe too. Then restart once. If F2 keeps coming back, an engineer needs to check the flue, the gas valve and the ignition parts. The flue is the pipe that takes fumes outside.
What do L9 and F9 mean on an Ideal boiler?
L9 and F9 mean there's a problem with the main circuit board. Ideal says the board may not be set up for the boiler, or may be faulty. On the Logic Combi2 (shown as L 09 or F 09), it can also mean a short on the gas valve.
There's nothing safe for you to check here. Ideal's guides tell householders to call a Gas Safe engineer. Don't keep restarting it.
What do other Ideal fault codes mean?
Most other Ideal codes point to a part inside the boiler, so they need a Gas Safe engineer. You can restart once for most of them. A few have checks you can do, which are listed below.
- F3: a fan fault.
- F4 or L4: a fault with the flow sensor, which measures the water leaving the boiler.
- F5 or L5: a return sensor fault on the Logic Combi ESP1 and Combi2. On an Instinct or an older Logic, L5 means too many resets instead (see LC).
- F6: an outside sensor fault. You'll only see it if a weather sensor is fitted.
- F7: the mains voltage is low. Ideal says to contact an electrician or your electricity supplier. We're electricians as well as gas engineers, so we can check your supply.
- L6: the boiler sees a flame when there shouldn't be one. Ideal says this needs an engineer.
- LC: five restarts in 15 minutes. Turn the power to the boiler off and on, then get it checked.
- L0: on the Logic Combi2, a blocked flue or condensate pipe. Do the same checks as L2.
- FU: the water going out is much hotter than the water coming back. Bleed the radiators, check the pressure, then restart. If it stays, there may be a blockage.
- FA: a sensor fault, or the flow and return pipes may be the wrong way round.
- F0C: on the Logic Combi2, a fault with the hot water sensor.
- dU: an engineer's setting used during a service, not a fault. Ideal says to turn the knobs fully clockwise, turn the power off and on, then press restart.
- C0 or C2: a fault with the boiler chip card. That's a small card on the circuit board that tells it which model it is.
- SE: a reminder that a service is due. Ideal says to contact your installer. A yearly boiler service is the right time to clear it.
- FD or L3: on some older Ideal boilers, no water flow. Bleed the radiators, check the pressure, then turn the boiler back on. If the code stays, call an engineer.
We've only listed meanings we could find in Ideal's own guides and FAQs. Older Ideal boilers may use other codes. If yours isn't here, check the manual or tell the engineer exactly what the screen shows.
What do 00, C and d mean on an Ideal boiler?
These are status codes, not faults. They show what the boiler is doing right now. 00 (or 0) is the most common, and it means standby: nothing is asking for heat or hot water.
- 0 or 00: standby. The boiler is waiting, which is normal.
- C: the heating is on, or the room has reached its set temperature.
- d: the boiler is heating hot water for a tap.
- P: preheat. It keeps the hot water side warm so taps run hot sooner.
- F on its own: frost protection is running.
- --: the mode knob is turned off.
C, d, P and F come from the Instinct guide. Newer models such as the Logic Combi ESP1 show the temperature with a radiator or tap symbol instead. There's one catch with 00. If you run a hot tap and the display stays on 00, the boiler isn't responding. Ideal says to call a Gas Safe engineer then. Our guide to heating that works with no hot water covers other checks.
How do I reset an Ideal boiler?
Ideal calls it a restart, and the button depends on your model. Restart once. If the same code comes back, stop and call a Gas Safe engineer.
- Logic Combi ESP1, Logic Code Combi and Logic Combi2: press the restart button. The boiler runs through its lighting steps again.
- Logic+ Combi2, Logic MAX Combi2 and Vogue: press the Restart key under the screen.
- Instinct and older Logic Combis: turn the mode knob to "reset", then straight back to your usual setting.
Ideal boilers stop you resetting too often. After five restarts in 15 minutes, the boiler blocks the reset. You may see LC, or "Too Many Restarts". Turn the power to the boiler off at its switch, then on again. Don't restart at all if you smell gas, or for L6, L9, F9, C0 or C2.
Our guide on how to reset a boiler, and when to stop explains why restarting over and over doesn't help. If the boiler stopped in a power cut, see boiler not working after a power cut.
Which Ideal boiler do I have?
The model name is on the front panel. It's also on the data badge, a sticker with the boiler's details. Common Ideal combis include the Logic Combi ESP1, Logic Code Combi ESP1, Logic Combi2, Logic+ Combi2, Logic MAX Combi2, Vogue and Instinct.
Older homes may have an Icos, Classic, Mini or Atlantic. We haven't listed codes for these, as they can differ. Ideal keeps user guides for current models on its website. Write the model down with the code. It helps the engineer.
Do you need a new boiler if your Ideal shows a fault code?
Usually not. Most Ideal codes come from a part that can be repaired or replaced. A sensor, fan, pump or electrode is a normal repair. Low pressure or a frozen pipe may need no parts at all.
A new boiler can be worth weighing up when:
- an older boiler needs a new circuit board, for example after L9 or F9
- the boiler is well over 10 years old and keeps showing different codes
- the parts for your model are no longer made
We'll talk it through with you and say plainly which makes more sense. Our guide to how long a boiler lasts can help you decide. If it's time for a new boiler, we fit all makes, starting with a free survey and a fixed price.
When to call a Gas Safe engineer
Call a Gas Safe engineer if a code returns after your checks and one restart. Call straight away for L6, L9, F9, C0 or C2, or any code you can't fix from the outside. By law, only a Gas Safe registered engineer may work on a gas boiler.
- L2 or F2 comes back even with gas, credit and a clear condensate pipe
- F1 returns within days of topping up
- L1, FU or LC comes back after one restart
- the boiler gurgles and locks out again after you've thawed the pipe
- you see soot or black marks round the boiler, or smell burning
A code is only a starting point. On the visit, the engineer first runs a thorough check of the boiler to find the fault and the parts it needs. We tell you the price before any work starts. Our boiler repair page lists the faults we fix.
Other boiler guides
- Worcester Bosch fault codes: what EA 227, CE 207, 224 and other codes mean.
- Vaillant fault codes: what F22, F28, F75 and other codes mean.
- Boiler losing pressure: what the gauge should read and how to top it up.
- Frozen condensate pipe: how to thaw it safely.
- Boiler keeps turning off: lockouts, short cycling and when to reset.
- Boiler won't turn on: the checks to try first.
- Boiler making noise: what banging, gurgling and kettling mean.
- Cold radiators: what cold at the top or bottom means.
- Heating works but no hot water: checks to try, and what a diverter valve does.
- Hot water but no heating: thermostat, timer and valve checks.
- Leaking boiler: what to do first, and where the water is coming from.
- Boiler pressure too high: what is too high, and how to lower it safely.
- Boiler tripping the electrics: why it trips the fuse box, and who to call.
- Boiler not working after a power cut: how to reset it, and set the timer clock.
- TRV not working: how to free a stuck pin, set the numbers or replace a head.
- Smell gas?: what to do straight away, and who to call.
- Carbon monoxide alarm beeping: what the beeps mean and what to do.
- How long does a boiler last?: signs it's wearing out, and repair or replace.
- Moving a boiler: where it can go, flues, gas pipes and the paperwork.
- Combi vs system boiler: stored hot water, cylinders and which suits your home.
- Combi vs regular boiler: loft tanks, heat-only boilers and switching to a combi.
- All common boiler problems.
Ideal code still showing? Get your boiler fixed by a Gas Safe engineer.
Common questions

How do I reset an Ideal boiler?
It depends on the model. On a Logic Combi ESP1, Logic Code Combi or Logic Combi2, press the restart button. On a Logic+ Combi2, Logic MAX Combi2 or Vogue, press the Restart key under the screen. On an Instinct or an older Logic Combi, turn the mode knob to reset and straight back. Do it once. If the code comes back, call a Gas Safe engineer. Read when to stop resetting a boiler.
Why does my Ideal boiler keep showing L2?
L2 means the boiler tried to light five times and failed. The usual outside causes are no gas, a prepayment meter out of credit, a closed gas valve under the boiler, or a blocked or frozen condensate pipe. If none of these is the cause, a part inside such as the ignition or the gas valve needs an engineer. Book a boiler repair.
Why is my Ideal boiler gurgling and showing L2?
Ideal says a blocked condensate pipe makes the boiler gurgle before it locks out on L2. In cold weather the pipe is often frozen. Thaw it with warm water, never boiling, then restart once. If it gurgles and locks out again, an engineer needs to check the trap inside the boiler. Read how to thaw a frozen condensate pipe.
What does 00 mean on an Ideal boiler?
00 (or 0 on some models) means standby. Nothing is asking for heating or hot water, so the boiler is waiting. That is normal. The one exception is when you run a hot tap and it stays on 00. Then the boiler is not responding, and Ideal says to call a Gas Safe engineer. Read our guide to no hot water.
Why won't my Ideal boiler reset?
After five resets in 15 minutes, an Ideal boiler stops letting you reset it. Many models then show LC, or "Too Many Restarts" on a screen. Turn the power to the boiler off at the switch, then back on. If the first code comes back after that, stop and call an engineer.
Can I fix an Ideal fault code myself?
Only with the outside checks Ideal lists for householders. You can top up the pressure, thaw the condensate pipe, check the gas meter and any prepayment credit, check the gas valve under the boiler is open, open radiator valves and restart once. Anything inside the boiler case is for a Gas Safe registered engineer.

Ideal code won't go away?
Call us to book a boiler repair. We repair all makes, Ideal included. A Gas Safe registered engineer will find the fault and tell you the price before starting.
