System boiler vs combi boiler: what's the difference?

A system boiler heats your radiators and keeps a cylinder of hot water ready to use. A combi boiler heats water straight from the mains the moment you turn on a tap, so it needs no cylinder. A system boiler usually suits homes with two or more bathrooms. A combi usually suits smaller homes, where one tap or shower runs at a time.

Updated 08/11/2026 · Express Contractors

Picking between these two comes down to one question. Do you want your hot water stored, or heated on the spot? Below, we cover what a system boiler is, what each part does, and how it stacks up against a combi. Planning a new boiler? We install both types, and a free survey shows which one fits your home. Has your boiler stopped working? Go to our boiler repair page. This guide is part of our common boiler problems series. Got tanks in the loft? Read combi vs regular boiler instead.

What is a system boiler?

A system boiler is a gas boiler that heats your radiators and a separate cylinder of stored hot water. It runs on a sealed system filled from the mains. So the heating needs no tank in the loft.

It gets its name because the main heating parts are built into the boiler. Inside the case you'll find:

  • A pump. It pushes hot water round the radiators and through the cylinder.
  • An expansion vessel. This is a small tank with a cushion of air inside. Water grows a little as it heats up, and the vessel soaks up the extra.
  • A pressure gauge. With the heating off, it should usually read about 1 to 1.5 bar.

The hot water lives in a cylinder, often in an airing cupboard. In most homes with a system boiler, it's an unvented cylinder. That means it's sealed and fed straight from the cold mains. Your hot water then comes out at mains pressure, much like the cold tap. Some older homes have a vented cylinder instead, fed by a cold tank in the loft.

How does a system boiler work?

A system boiler heats water in a sealed loop of pipes, then sends it to your radiators or the cylinder. The cylinder holds the hot water until you need it. Here's what happens, in order.

  1. Your timer or thermostat asks for heat.
  2. The boiler lights and heats the water in its sealed loop.
  3. The pump sends that water to the radiators, the cylinder, or both.
  4. A zone valve picks the route. It's a valve with a small motor that opens and closes each route.
  5. Inside the cylinder, the hot water passes through a coiled pipe and warms the stored water around it.
  6. When you open a hot tap, mains pressure pushes the stored water out. Cold water refills the cylinder from the bottom.

Most people set the hot water to come on before they need it, such as early morning. The cylinder is wrapped in insulation, so the water stays hot for hours. Most cylinders also have an immersion heater. It works like a big kettle element, run on electricity, so the cylinder can still warm up when the boiler is off.

Does a combi boiler need a water tank?

No. A combi boiler needs no water tank and no cylinder. It heats cold mains water as it flows through the boiler, the moment you open a hot tap. That's the big difference from a system boiler, which keeps a store of hot water ready.

On the wall, a combi and a system boiler can look almost the same. The difference is elsewhere in the house. A system boiler sends heat to a cylinder in a cupboard, but a combi has no cylinder to send it to. So if you find a big hot water tank upstairs, you don't have a combi.

Safety first

Smell gas? Open doors and windows. Don't use light switches or anything that could spark. Turn the gas off at the meter if you can do it safely. Then go outside and call the National Gas Emergency number on 0800 111 999.

Headaches, dizziness, sickness or a lazy yellow flame? These can be signs of carbon monoxide (CO), a poison gas you can't see or smell. Turn the boiler off, open windows, get everyone outside and call 0800 111 999. See a doctor if anyone feels unwell. Our carbon monoxide advice has more.

Never open the boiler case. Only a Gas Safe registered engineer should take the cover off a gas boiler. The checks in our guides are all ones you can do from the outside.

System boiler vs combi: the main differences

The main difference is where the hot water comes from: a store in a cylinder, or heated on the spot. That one difference changes how many taps you can run, how much space you need and how you plan your hot water.

What you'll noticeSystem boilerCombi boiler
Hot waterHeated ahead of time and storedHeated as you use it
Two showers at onceBoth run well from the stored waterThe flow is shared, so both feel weaker
Running outCan run out, then needs time to heat up againWon't run out, but comes at a steady flow
SpaceThe boiler, plus a cupboard for the cylinderJust the boiler
If the boiler failsWater already stored, and usually an immersion heater tooNo hot water until it's fixed
Usually suitsTwo or more bathrooms, busy homesOne bathroom, smaller homes and flats

Can a system boiler run several taps at once?

Yes, and this is where it does best. The shower, the bath and the kitchen tap all draw from the same store of hot water. A combi has to heat every drop as it goes. Run two hot taps at once, and the flow gets split between them.

Which has better water pressure?

Both use mains pressure, as long as the system boiler has an unvented cylinder. Pressure is how hard the water pushes. Flow is how much comes out each minute. Both types need a good mains supply to work well. That's why your mains pressure and flow get checked at a survey, before anyone picks a boiler.

How much space does each one need?

A system boiler needs room for the cylinder, usually a tall cupboard. An unvented cylinder also needs a small pipe to carry water safely outside if its safety valve ever opens. A combi needs only a spot on the wall, so it often suits flats and small houses. Moving from a cylinder to a combi frees up that cupboard.

How long does a system boiler take to heat water?

A cylinder heated from cold takes a while. How long depends on its size and the boiler. That's why most people use a timer, so the water is ready when they wake up. Once the cylinder is hot, water comes out straight away. A combi starts heating the moment you open the tap. You only wait for the cold water in the pipe to clear.

What does each one look like at home?

With a system boiler, you'll see the boiler on the wall with a pressure gauge on the front. Somewhere else, often upstairs, there's a cylinder. An unvented one usually has valves and a small round tank fixed near it. With a combi, there's just the boiler. There's no cylinder, and usually no tanks in the loft.

Which suits your home: a system boiler or a combi?

Count your bathrooms, and think about how many people use hot water at the same time. Those two things settle most choices. Space and your mains water supply come next.

A system boiler often suits you if:

  • you have two or more bathrooms, or a bathroom and an en-suite
  • two people often shower at the same time in the morning
  • you have room for a cylinder, or one is already there
  • you like having an immersion heater as a backup for hot water

A combi often suits you if:

  • you have one bathroom
  • you live in a flat or a smaller house
  • you'd like the cylinder cupboard back for storage
  • hot water is mostly used one tap at a time

Boiler size, measured in kilowatts (kW), matters too, and our boiler installation page explains how it's picked.

We install system boilers and combis from every maker, and we convert homes from one to the other. The free survey looks at your home, your bathrooms and your mains water. Then you get our honest view and a fixed price. A like-for-like swap typically takes 1 day. For a conversion, we'll tell you at the survey how long it should take. All our work is guaranteed for 12 months, parts and labour.

How do you look after a system boiler and cylinder?

Book a yearly boiler service, and have an unvented cylinder checked each year too. Most cylinder makers ask for a yearly check to keep the warranty valid. The check makes sure its safety valves still work.

  • An unvented cylinder must be fitted by someone with the right qualification, often called G3. That's a building regulations rule, because the cylinder is under pressure.
  • A sealed system needs clean water. A magnetic filter catches bits of rust before they reach the boiler. If sludge has built up, a power flush can wash it out.
  • If the pressure gauge keeps dropping, read our guide to a boiler losing pressure.

We service unvented cylinders and replace old ones. Faulty immersion heaters, zone valves and pumps are jobs we fix too, and our plumber page has more on cylinder work. To keep the boiler itself in good shape, book a yearly boiler service. Most boilers last about 10 to 15 years, as our guide to how long a boiler lasts explains.

When to call a Gas Safe engineer

Ring a Gas Safe engineer when a system boiler stops working or the cylinder goes cold. For advice on a new boiler, book a free survey instead. Gas boilers can only be worked on by a Gas Safe registered engineer. That's the law.

  • the boiler shows a fault code that won't clear
  • the heating works but the cylinder stays cold
  • water keeps dripping from the cylinder's safety pipe
  • you need to top up the boiler pressure often
  • you're torn between a system boiler and a combi

For a breakdown, see boiler repair. No hot water at all? Read our guide to heating that works but no hot water. Thinking of replacing your boiler? We start with a free survey.

Other boiler guides

Want stored hot water, or hot water on demand? We'll help you weigh it up at a free survey, then fix the price before any work starts.

Common questions

Bob, the Express Contractors mascot, thinking
Is a system boiler better than a combi?

Neither is better for every home. A system boiler is better when several people need hot water at the same time, because it keeps a store ready. A combi is better when space is tight and hot water is used one tap at a time. The number of bathrooms is usually the deciding point.

Can a system boiler work without a hot water cylinder?

It can heat your radiators without one, but it can't give you hot water at the taps. A system boiler is made to heat a cylinder of stored water. If you don't want a cylinder at all, a combi is the type that heats water on its own.

Does a system boiler need a tank in the loft?

Not usually. The heating side is sealed and filled from the mains, and an unvented cylinder takes its water from the mains too. Some older homes pair a system boiler with a vented cylinder, which still has a cold water tank in the loft.

Is a system boiler cheaper to run than a combi?

They cost much the same to run. A cylinder loses a little heat as it stands, while a combi only heats the water you use. In a busy home that uses lots of hot water, the gap is small. How you set the timer and thermostat matters more than the boiler type.

What happens if a system boiler breaks down?

The heating stops, and the boiler can't reheat the cylinder. Most cylinders have an immersion heater, though. Switch it on and you can still heat water with electricity until the boiler is fixed. Any hot water already in the cylinder stays warm for a while too. See our boiler repair page.

Can I swap a system boiler for a combi?

Usually, yes, and it's a job we do. The cylinder comes out, and the pipes are changed so the combi feeds the hot taps. Your mains water pressure and flow need checking first, as a combi relies on them. You also lose the stored hot water and the immersion heater backup. Book a free survey.

Bob, the Express Contractors mascot, showing a new boiler

Not sure which boiler suits your home?

Call us to book a free survey. A Gas Safe registered engineer will look at your home and tell you honestly which type makes sense. Then you get a fixed price.

Call now · 0121 517 0785